基本信息
标准名称: | 压力式六氟化硫气体密度控制器 |
英文名称: | Pressure Type SF6 Gas Density Monitors |
发布部门: | 中华人民共和国国家质量监督检验检疫总局 |
发布日期: | 2011-12-28 |
实施日期: | 2012-03-28 |
首发日期: | |
作废日期: | |
主管部门: | 全国压力计量技术委员会 |
归口单位: | 全国压力计量技术委员会 |
起草单位: | 河南省计量科学研究院、上海市计量测试技术研究院、郑州赛奥电子股份有限公司、西安热工研究院有限公司、红旗仪表有限公司 |
起草人: | 孙晓全、屠立猛、张灿利、史亚丽、张晓明、周春龙 |
出版社: | 中国质检出版社 |
出版日期: | 2012-03-28 |
页数: | 16页 |
书号: | 155026·J-2673 |
适用范围
本规程适用于测量范围为(-0.1~0.9)MPa、以弹簧管为测量元件、带有温度补偿装置并具有接点输出功能的压力式六氟化硫(SF6)气体密度控制器或称气体密度继电器的首次检定、后续检定和使用中检查。
前言
没有内容
目录
1 范围 (1)
2 引用文件 (1)
3 术语和定义 (1)
4 概述 (1)
5 计量性能要求 (2)
5.1 准确度等级及示值误差 (2)
5.2 回程误差 (2)
5.3 零位误差 (2)
5.4 额定压力值误差 (2)
5.5 轻敲位移 (2)
5.6 密封性 (2)
5.7 指针偏转平稳性 (2)
5.8 设定点偏差及切换差 (2)
5.9 温度补偿误差 (3)
6 通用技术要求 (3)
6.1 外观结构 (3)
6.2 绝缘电阻 (3)
6.3 介电强度 (4)
7 计量器具控制 (4)
7.1 检定条件 (4)
7.2 检定项目 (4)
7.3 检定方法 (5)
7.4 检定结果处理 (6)
7.5 检定周期 (6)
附录A SF6 气体密度控制器检定记录格式 (7)
附录B 检定证书内页格式 (9)
附录C 检定结果通知书内页格式 (10)
引用标准
本规程引用下列文件:
JJG52—1999 弹簧管式一般压力表、压力真空表和真空表
GB/T22065—2008 压力式六氟化硫气体密度控制器
凡是注日期的引用文件,仅注日期的版本适用于本规程;凡是不注日期的引用文件,其最新版本(包括所有的修改单)适用于本规程。
所属分类: 综合 标准化管理与一般规定 技术管理 社会学 服务 公司(企业)的组织和管理 行政 运输 质量 质量管理和质量保证
【英文标准名称】:StandardSpecificationforLock-StripGaskets
【原文标准名称】:带状锁紧垫圈标准规范
【标准号】:ASTMC542-2005
【标准状态】:现行
【国别】:
【发布日期】:2005
【实施或试行日期】:
【发布单位】:美国材料与试验协会(US-ASTM)
【起草单位】:C24.73
【标准类型】:(Specification)
【标准水平】:()
【中文主题词】:密封;建筑;密封材料;密封件
【英文主题词】:compression;elastomer;elastomeric;gasket;locking;lock-strip;preformed;seal;strip;zipper
【摘要】:1.1Thisspecificationdefinestherequiredpropertiesoflock-stripgasketswhereresistancetosunlight,weathering,flame,oxidation,permanentdeformationunderload,anddiminutionofgrippingpressureareprimeessentials.Note18212;Therequirementofflamepropagationmaybewaivedbythearchitectorprofessionalengineerwhendoingsodoesnotconflictwithlocalcodesorordinances.1.2Thisspecificationappliesonlytothe"locking"compressiontypeofgasket,sometimesreferredtoasthe"zipper"type.Note28212;Structuralintegrityandweather-tightnessofthewallrequiresthesounddesignandinstallationoftheentiresystemofwhichthegasketisonlyonecomponent.1.3ThevaluesstatedinSIunitsaretoberegardedasthestandard.1.4TestMethodC1166,asreferencedinthisspecification,shouldbeusedtomeasureanddescribethepropertiesofmaterials,products,orassembliesinresponsetoheatandflameundercontrolledlaboratoryconditionsandshouldnotbeusedtodescribeorappraisethefirehazardorfireriskofmaterials,products,orassembliesunderactualfireconditions.However,resultsofthistestmaybeusedaselementsofafireriskassessmentwhichtakesintoaccountallofthefactorswhicharepertinenttoanassessmentofthefirehazardofaparticularenduse.1.5Thefollowingprecautionarycaveatpertainsonlytothetestmethodportion,Section7,ofthisspecification:Thisstandarddoesnotpurporttoaddressthesafetyconcerns,ifany,associatedwithitsuse.Itistheresponsibilityoftheuserofthisstandardtoestablishappropriatesafetyandhealthpracticesanddeterminetheapplicabilityofregulatorylimitationspriortouse.1.6Thecommitteewithjurisdictionoverthisstandardisnotawareofanycomparablestandardspublishedbyotherorganizations.
【中国标准分类号】:J13
【国际标准分类号】:91_100_50
【页数】:5P.;A4
【正文语种】: